Hyundai i-30: Automatic transmission / Good driving practices
- Never move the shift lever from P
(Park) or N (Neutral) to any other
position with the accelerator pedal
depressed.
- Never move the shift lever into P
(Park) when the vehicle is in
motion.
Be sure the vehicle is completely
stopped before you attempt to shift
into R (Reverse) or D (Drive).
- Do not move the shift lever to N
(Neutral) when driving. Doing so
may result in an accident because
of a loss of engine braking and the
transmission could be damaged.
- Do not drive with your foot resting
on the brake pedal. Even light, but
consistent pedal pressure can
result in the brakes overheating,
brake wear and possibly even
brake failure.
- When driving in manual shift mode,
slow down before shifting to a
lower gear. Otherwise, the lower
gear may not be engaged if the
engine rpms are outside of the
allowable range.
- Always apply the parking brake
when leaving the vehicle. Do not
depend on placing the transmission
in P (Park) to keep the vehicle
from moving.
- Exercise extreme caution when
driving on a slippery surface. Be
especially careful when braking,
accelerating or shifting gears. On a
slippery surface, an abrupt change
in vehicle speed can cause the
drive wheels to lose traction and
may cause loss of vehicle control
resulting in an accident.
- Optimum vehicle performance and
economy is obtained by smoothly
depressing and releasing the
accelerator.
WARNING
To reduce the risk of SERIOUS
INJURY or DEATH:
- ALWAYS wear your seat belt.
In a collision, an unbelted
occupant is significantly more
likely to be seriously injured
or killed than a properly belted
occupant.
- Avoid high speeds when cornering
or turning.
- Do not make quick steering
wheel movements, such as
sharp lane changes or fast,
sharp turns.
- The risk of rollover is greatly
increased if you lose control
of your vehicle at highway
speeds.
- Loss of control often occurs if
two or more wheels drop off
the roadway and the driver
over steers to reenter the
roadway.
- In the event your vehicle
leaves the roadway, do not
steer sharply. Instead, slow
down before pulling back into
the travel lanes.
- HYUNDAI recommends you
follow all posted speed limits.
Information - Kickdown
Mechanism (if equipped)
Use the kickdown mechanism for
maximum acceleration. Depress the
accelerator pedal beyond the pressure
point. The automatic transmission will
shift to a lower gear depending on the
engine speed.
Always come to a complete stop and
continue to depress the brake pedal.
Move the shift lever into the P (Park)
position, apply the parking brake,
and place the ignition switch in the
LOCK/OFF position...
Dual clutch transmission operation
The dual clutch transmission has seven forward speeds and one reverse
speed. The individual speeds are selected automatically when the shift lever
is in the D (Drive) position...
Other information:
1. Position the vehicles close enough
that the jumper cables will reach,
but do not allow the vehicles to
touch.
2. Avoid fans or any moving parts in
the engine compartment at all
times, even when the vehicles are
turned off.
3. Turn off all electrical devices such
as radios, lights, air conditioning,
etc...
Components and components location
Components
No
Connector A
Connector B
Connector C
1
-
IGN 2 Relay output
Battery signal
2
SSB Switch 1 input
C CAN (Low)
-
3
Driver door antenna switch input
C CAN (High)
Immoblizer antenna power
4
-
B CAN (High)
Driver out side handle antenna power
5
-
B CAN (Low)
Assist out side handle antenna power
6
-
SSB Illumination (orange)
Bumper antenna power
7
RPM Input
-
Interior antenna 1 power
8
Start signal feedback input
SSB Illumination (+) output
Interior antenna 2 power
9
clutch switch input
ESCL enable output
Interior antenna 3 power
10
-
Battery power
-
11
Starter relay output
IGN 1 Relay output
-
12
Power 1
ESCL COM
-
13
SSB Switch 2 input
EMS COM
ESCL (-) output
14
Assist door antenna switch input
-
Immoblizer antenna ground
15
-
SSB Illumination (-) output
Driver out side handle antenna ground
16
Clutch switch input
SSB LED Output
Assist out side handle antenna ground
17
ESCL unlock swtich input
SSB LED IGN Output
Bumper antenna ground
18
Wheel speed sensor input
External buzzer
Interior antenna 1 ground
19
ACC Input
-
Interior antenna 2 ground
20
IGN 1
ESCL (+) output
Interior antenna 3 ground
21
Brake switch input
-
22
ACC Relay input
GND Power 2
Schematic diagrams
Circuit Diagram
Repair procedures
Removal
Smart Key Unit
1...
Categories
(1) Driver’s door power window
switch
(2) Front passenger’s door power
window switch
(3) Rear door (right) power window
switch
(4) Rear door (left) power window
switch
(5) Window opening and closing
(6) Automatic power window
(7) Power window lock switch
read more