Hyundai i-30: Exterior lights / Warning light and message
When the High Beam Assist (HBA)
System is not working properly, the
warning message will come on for a
few second. After the message disappears,
the master warning light ()
will illuminate.
We recommend that you take your
vehicle to a HYUNDAI authorised
repairer and have the system
checked.
CAUTION
The system may not operate
normally if any of the following
conditions should occur:
1) When the illumination from
an on-coming vehicle or a
vehicle in front is dim. Such
examples may include:
- When the headlamps of an
oncoming vehicle or the tail
lamps of a vehicle in front is
covered with dust, snow, or
water
- When the headlamps on an
on-coming vehicle are OFF,
but the fog lamps are ON)
2) When the High Beam Assist
camera is adversely affected
by an external condition. Such
examples may include:
- When the vehicle's headlamps
have been damaged or
not repaired properly
- When the vehicle headlamps
are not aimed properly
- When the vehicle is driven on
a narrow curved road or rough
road
- When the vehicle is driven on
an uphill road or downhill
road
- When only part of the vehicle
in front is visible on a crossroad
or curved road
- When there is a traffic light,
reflecting sign, flashing sign
or mirror
- When the road conditions are
bad such as being wet or covered
with snow
- When a vehicle suddenly
appears from a curve
- When the vehicle is tilted from
a flat tyre or being towed
- When the Lane Keeping
Assist (LKA) system warning
light illuminates
- When the light from the
oncoming or front vehicle is
not detected because of
exhaust fume, smoke, fog,
snow, etc.
- When the front window is covered
with foreign matters
such as
3) When the forward visibility is
poor. Such examples may
include:
- When the headlamps of an
oncoming vehicle or a vehicle
in front is not detected due to
poor outside visibility (smog,
smoke, dust, fog, heavy rain,
snow, etc.)
- When the windscreen visibility
is poor
Information
When you replace or reinstall the
windscreen glass or LDW/LKA camera
(if equipped), We recommend that
you take your vehicle to a HYUNDAI
authorised repairer and have the system
checked.
WARNING
- Do not attempt to disassemble
the front view camera without
the assistance of a HYUNDAI
authorised repairer technician.
If camera is removed for any
reason, the system may need
to be re-calibrated. We recommend
that the system be
inspected by a HYUNDAI
authorised repairer.
- If the windscreen of your vehicle
is replaced, most likely the
front view camera will need to
be re-calibrated. If this occurs,
have your vehicle inspected
and have the system re-calibrated
by a HYUNDAI authorised
repairer.
- Be careful that water doesn’t
get into the High Beam Assist
(HBA) unit and do not remove
or damage related parts of the
High Beam Assist (HBA) system.
- Do not place objects on the
crash pad that reflect light
such as mirrors, white paper,
etc. The system may malfunction
if sunlight is reflected.
- At times, the High Beam Assist
(HBA) may not work properly.
The system is for your convenience
only. It is the responsibility
of the driver for safe driving
practices and always check the
road conditions for your safety.
- When the system does not
operate normally, change the
lamp position manually
between the high beam and
low beam.
The High Beam Assist (HBA) is a
system that automatically adjusts the
headlamp range (switches between
high beam and low beam) according
to the brightness of other vehicles
and road conditions...
To signal a turn, push down on the
lever for a left turn or up for a right
turn in position (A). To signal a lane
change, move the turn signal lever
slightly and hold it in position (B)...
Other information:
Components and components location
Component Location
1. Lumber support
motor (Horizontal)
2. Rear height motor
3. Reclining motor
4. Slide motor
5. Front tilt
motor
6. Reclining limit switch
7...
Components and components location
Components
Repair procedures
Inspection
1.
Disconnect the negative (-) battery terminal.
2.
Open the sunglass case cover from the overhead console and remove the
2 screws holding the overhead console...
Categories
When the High Beam Assist (HBA)
System is not working properly, the
warning message will come on for a
few second. After the message disappears,
the master warning light ()
will illuminate.
read more