Hyundai i-30: Tires/Wheels / Wheel
		
		
		Repair procedures
	
		| Hub nut tightening sequence | 
	
	
		| 
		1. | 
		
		 
			Tighten the hub nuts as follows. 
		
			
				| 
				 
					Tightening torque :  
				
					107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft) 
				 | 
			 
		 
		
		  
		
			
				
				
				
					
						| 
						•  | 
						
						 
							When using an impact gun, final tightening torque should 
							be checked using a torque wrench. 
						 | 
					 
				 
				 | 
			 
		 
		
			
				| 
				
				 
					If the vehicle starts within 19 minutes after the replacement 
					of the wheel of the stopped vehicle, the TPMS Malfunction Indicator 
					on the instrument cluster illuminates. 
				
					
						| 
						–  | 
						
						 
							The above symptom is due to communication failure between 
							the BCM and the replaced TPMS ID. 
						 | 
					 
				 
				
					
						| 
						–  | 
						
						 
							This communication failure indicator turns off in 19 
							minutes after the vehicle stops through the BCM’s automatic 
							learning process of TPMS ID. 
						
							(When driving the vehicle after stopping for over 19 
							minutes, the indicator turns off automatically.)
						 
						 | 
					 
				 
				 | 
			 
		 
		 | 
	
	Run out inspection
	
		| 
		2. | 
		
		 
			Measure the wheel Run-out by using a dial indicator as illustration 
			below. 
		
			 
		
			
				
				Run-out  
				 | 
				
				Aluminum  
				 | 
			 
			
				
				Radial mm (in.) 
				 | 
				
				Below 0.3 (0.0118) 
				 | 
			 
			
				
				Lateral mm (in.) 
				 | 
				
				Below 0.3 (0.0118) 
				 | 
			 
		 
		 
		 | 
	
	
		| 
		3. | 
		
		 
			If measured value exceeds the standard value, replace the wheel. 
		
		  
		 | 
	
   Repair procedures
	
		Tire Wear
	
	
		
		1.
		
		
			Measure the tread depth of the tires.
		
			
				
				
					Tread depth [limit] : 1...
   
 
   Repair procedures
	
		Front wheel alignment
	
	
		
		
			
				
				
				   
			
			
				
			
		
		
			
				•
				
				
				
					When using a commercially available computerized wheel alignment 
					equipment to inspect the front wheel alignment, always position 
					the vehicle on a level surface with the front wheels facing 
					straight ahead...
   
 
   Other information:
   Repair procedures
	
		Removal
	
	
		
		1.
		
		
			Disconnect the negative (-) battery terminal.
		
	
	
		
		2.
		
		
			Remove the front seat assembly.
		
			(Refer to Body - "Front Seat Assembly")
		
	
	
		
		3...
   
   Repair procedures
	
		Tire Wear
	
	
		
		1.
		
		
			Measure the tread depth of the tires.
		
			
				
				
					Tread depth [limit] : 1.6 mm (0.063 in)
				
			
		
		
	
	
		
		2.
		
		
			If the remaining tread depth (A) is less than the limit, replace the 
			tire...
   
 
	 
	
        
		Categories
		
		
If your vehicle is equipped with a 
sunroof, you can slide or tilt your 
sunroof with the sunroof control lever 
located on the overhead console.

The ignition switch must be in the ON 
position before you can open or 
close the sunroof.
The sunroof can be operated for 
approximately 30 seconds after the 
ignition key is removed or turned to 
the ACC or LOCK(or OFF) position. 
However, if the front door is opened, 
the sunroof cannot be operated even 
within 30 seconds.
read more