Hyundai i-30: Engine Control System / Intake Air Temperature Sensor (IATS)

Hyundai i30 (PD) 2018-2025 Service Manual / Engine Control / Fuel System / Engine Control System / Intake Air Temperature Sensor (IATS)

Description and operation

Description

Intake Air Temperature Sensor (IATS) is included inside Manifold Absolute Pressure Sensor and detects the intake air temperature.

To calculate precise air quantity, correction of the air temperature is needed because air density varies according to the temperature. So the ECM uses not only MAPS signal but also IATS signal. This sensor has a Negative Temperature Coefficient (NTC) Thermister and it's resistance changes in reverse proportion to the temperature.

Specifications

Specification

Temperature		Resistance (kΩ)
°C	°F	Resistance (kΩ)
-40 ± 1	-40 ± 1	38.88 - 50.77
-20 ± 1	-4 ± 1	13.20 - 16.83
0 ± 1	32 ± 1	5.12 - 6.12
20 ± 1	68 ± 1	2.20 - 2.69
25 ± 1	77 ± 1	1.81 - 2.21
40 ± 1	104 ± 1	1.02 - 1.27
60 ± 1	140 ± 1	0.52 - 0.65
80 ± 1	176 ± 1	0.28 - 0.35
100 ± 1	212 ± 1	0.16 - 0.21
120 ± 1	248 ± 1	0.10 - 0.13
130 ± 1	266 ± 1	0.08 - 0.10
150 ± 1	302 ± 1	0.05 - 0.07

Schematic diagrams

Circuit Diagram

Harness Connector

Repair procedures

Inspection

1.	Turn the ignition switch OFF.

2.	Disconnect the IATS connector.

3.	Measure resistance between the IATS terminals 3 and 4.

Check that the resistance is within the specification.

Specification : Refer to "Specification"

Removal

1.	Turn the ignition switch OFF and disconnect the battery negative (-) cable.

2.	Disconnect the manifold absolute pressure sensor connector (A).

Remove the installation bolt (B), and then remove the sensor from the surge tank.

Tightening Torque :

9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

Installation

•	Install the component with the specified torques.

•	Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing.

•	Insert the sensor in the installation hole and be careful not to damage.

1.	Install in the reverse order of removal.

Manifold Absolute Pressure Sensor (MAPS)

Description and operation Description Manifold Absolute Pressure Sensor (MAPS) is a speed-density type sensor and is installed on the surge tank...

Ambient Temperature Sensor (ATS)

Description and operation Description Ambient Temperature Sensor (ATS) is installed on the front-end module and senses the ambient temperature...

Other information:

Hyundai i30 (PD) 2018-2025 Service Manual: Front Impact Sensor (FIS)

Components and components location Components 1. Front Impact Sensor (FIS) Description and operation Description • The front impact sensors (FIS) are installed on the upper of the side panel in Front End Module (FEM)...

Hyundai i30 (PD) 2018-2025 Owner's Manual: Sunvisor

To use a sunvisor, pull it downward. To use a sunvisor for a side window, pull it downward, unsnap it from the bracket (1) and swing it to the side (2). To use the vanity mirror, pull down the sunvisor and slide the mirror cover (3). Use the ticket holder (4) to hold tickets...