Hyundai i-30: Lubrication System / Engine Oil
Repair procedures
Engine Oil and Filter Replacement |
•
|
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dryness,
irritation and dermatitis. In addition, used engine oil contains
potentially harmful contaminants which may cause skin cancer.
|
•
|
Exercise caution in order to minimize the length and frequency
of contact of your skin to used oil. Wear protective clothing
and gloves. Wash your skin thoroughly with soap and water, or
use water-less hand cleaner, to remove any used engine oil.
Do not use gasoline, thinners, or solvents.
|
•
|
In order to preserve the environment, used oil and used oil
filter must be disposed of only at designated disposal sites.
|
|
1. |
Drain the engine oil.
(1) |
Remove the oil filler cap (A).

|
(2) |
Remove the engine oil service cover (A).

|
(3) |
Remove the oil drain plug (A) and drain the oil into a container.

|
|
2. |
Replace the oil filter.
(1) |
Remove the engine oil filter service cover (A).

|
(2) |
Remove the oil filter (A) with the SST (09263-2E000).

|
(3) |
Check and clean the oil filter installation surface.
|
(4) |
Check the part number of the new oil filter is as same as old
one.
|
(5) |
Apply clean engine oil to the gasket of a new oil filter.
|
(6) |
Lightly screw the oil filter into place, and tighten it until
the gasket contacts the seat.
Tighten it with the torque below.
Tightening torque :
11.8 - 15.7 N.m (1.2 - 1.6 kgf.m, 8.7 - 11.6 lb-ft)
|
|
|
3. |
Fill with engine oil.
(1) |
Clean and install the oil drain plug with a new gasket.
Tightening torque :
34.3 - 44.1 N.m (3.5 - 4.5 kgf.m, 25.3 - 32.5 lb-ft)
|
|
(2) |
Fill with new engine oil.
pacity
Total : 4.3(1.13 U.S.gal., 4.54 U.S.qt., 3.78 lmp.qt.)
- 4.6 L (1.21 U.S.gal., 4.86 U.S.qt., 4.04 lmp.qt.)
Oil pan : 3.8 L (1.00 U.S.gal., 4.01 U.S.qt., 3.34 lmp.qt.)
Drain and refill including oil filter : 4.2 L (1.10
U.S.gal., 4.43 U.S.qt., 3.69 lmp.qt.)
|
|
|
4. |
Install the oil filler cap.
|
5. |
Install the service cover.
|
6. |
Start engine and check for oil leaks.
|
7. |
echeck the engine oil level.
|
1. |
Check the engine oil quality.
Check for oil deterioration, entry of water, discoloring of thinning.
If the quality is visibly poor, replace the oil.
|
2. |
Check the engine oil level.
After warming up the engine, Turn the engine off and wait for a few
minutes(about 10 minutes) for the oil to return to the oil pan And check
the oi level.
The level should be between the "L" and "F" marks on the dipstick.
If low, check for oil leakage and add oil up to the "F" mark on the
dipstick.
|
Selection of Engine Oil
Specifications :
0W-20 / API SN + / SP or ILSAC GF-6
Allowed SAE Viscosity

Components and components location
Components
1. Cylinder block
3. Oil pump sproket
2. Oil pump
Repair procedures
Removal And Installation
Oil Pump
1...
Other information:
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to
depress the brake pedal. Move
the shift lever into the P (Park)
position, then apply the parking
brake, and place the ignition
switch in the LOCK/OFF position...
Description and operation
Description
Introduction of Quick Brake Warning System (ESS)
In case of quick brake by driver, the brake lamp or turn signal is blinked to
warn against the vehicle at rear.
1.
Basic function (Blinking the brake lamp/emergency lamp)
–
Operation condition : In case of quick brake or operation of
ABS above in a certain speed
–
Releasing condition : In case of stopping the quick brake or
releasing the ABS operation
2...
Categories

1. Driver’s front air bag
2. Passenger’s front air bag
3. Side air bag*
4. Curtain air bag*
5. Knee air bag*
6. Front passenger air bag ON/OFF
switch
read more