Hyundai i-30: Driving your vehicle
WARNING
Carbon monoxide (CO) gas is toxic. Breathing CO can cause unconsciousness
and death.
Engine exhaust contains carbon monoxide which cannot be seen or smelled.
Do not inhale engine exhaust.
If at any time you smell engine exhaust inside the vehicle, open the
windows immediately. Exposure to CO can cause
unconsciousness and death by asphyxiation.
Be sure the exhaust system does not leak.
The exhaust system should be checked whenever the vehicle is raised to
change the oil or for any other purpose. If
you hear a change in the sound of the exhaust or if you drive over something
that strikes the underneath side of the
vehicle, we recommend that the exhaust system be checked as soon as possible by
a HYUNDAI authorised repairer.
Do not run the engine in an enclosed area.
Letting the engine idle in your garage, even with the garage door open, is
a hazardous practice. Run the engine only
long enough to start the engine and to move the vehicle out of the garage.
Avoid idling the engine for prolonged periods with people inside the
vehicle.
If it is necessary to idle the engine for a prolonged period with people inside
the vehicle, be sure to do so only in an
open area with the air intake set at "Fresh" and fan control set to high so
fresh air is drawn into the interior.
Keep the air intakes clear.
To assure proper operation of the ventilation system, keep the ventilation
air intakes located in front of the windscreen
clear of snow, ice, leaves, or other obstructions.
If you must drive with the tailgate open:
Close all windows.
Open instrument panel air vents.
Set the air intake control at "Fresh", the air flow control at "Floor" or
"Face", and the fan control set to high.
To install or remove a roof carrier,
you can use the mounting bracket
and cover on the roof.
When you install a roof carrier, use
the following procedure...
Before entering the vehicle
Be sure all windows, outside mirror(
s), and outside lights are clean
and unobstructed.
Remove frost, snow, or ice...
Other information:
Components and components location
Components
TFT LCD Cluster (Standard)
TFT LCD Cluster (7Inch)
Connector Pin Information
Connector Pin Information
No.
Description
No.
Description
1
Ground
21
Trip switch (-)
2
Illumination (-)
22
Trip switch 1 (+)
3
Rheostat switch (Down)_Input
23
Trip switch 2 (+)
4
Rheostat switch (Up)_Input
24
M/T N switch
5
Dentent
25
Driver mode switch
6
P
26
-
7
R
27
-
8
N
28
Low washer level sensor
9
D
29
M-CAN (Low)
10
S
30
M-CAN (High)
11
Immobillizer
31
-
12
Vehicle speed_Output
32
C-CAN (High)
13
Alternator_Input
33
C-CAN(Low)
14
Fuel sender (+)_Input
34
-
15
-
35
-
16
Fuel sender (-)_Input
36
-
17
Water separator (+)
37
Ground
18
Airbag (+)_Input
38
-
19
Oil press switch (-)_Input
39
IGN 1
20
Tail_input
40
Battery (+)
Schematic diagrams
Circuit Diagram
TFT LCD Cluster (Standard)
TFT LCD Cluster (7Inch)
Description and operation
Description
Communication Network Diagram
Abbreviation
Expalnation
ECM
Engine Control Module
TCU
Transmission Control Unit
MDPS
Motor Driven Power Steering
AEB
Autonomous Emergency Braking
LKAS
Lane Keeping Assist System
FPS
Fuel Pump Control module
RR CAMERA
Rear View Carmera
VACUUM
Vacuum Pump
CLUSTER
Cluster Module
ACU
Airbag Control Unit
DATC
Dual Automatic Temp Control
MTC
Temp Control
OCS
Occupant Classification System
VDC
Vehicle Dynamic Control
BSD
Blind Spot Detection
AMP
Amplifier
AVN
Head Unit (Audio / AVN)
SMK
Smart Key Unit
WPC
Wireless Power Charger
IMS
Integrated Memory System
DDM
Driver Door Module
ADM
Assist Door Module
BCM
Body Control Module
B-CAN
Body Controller Area Network
P-CAN
Powertrain Controller Area Network
M-CAN
Multi media Controller Area Network
C-CAN
Chassis Controller Area Network
Cluster Variant Coding
As we have more options (ESC, MDPS etc...
Specifications
[Memory Power Seat Unit ]
Item
Specifications
Rated voltage
DC 12V
Operating Voltage
DC 9V - 16V
Operating Temperature Range
-30°C to 75°C
Dark current
Max...